Tooliom-TL-250-Pro-notes.txt



MIG Accessory Kits: Lincoln/magnum 100L & Tweco Mini #1
50 dinse plugs
arround 11.0 Watts idle
Input cord: 3x12 AWG With NEMA 6-50 Plug ~ 6 feet long
Adapter: ~ 1 foot
running off 2500 Watt modified sine wave inverter (no load)
	117.6 - 118.0 volts
	Idle 11.3 - 11.0 Watts
	62.5 Hz, 0.98 - 0.97 Power Factor (PF)

110 Volt values:
Synergic MIG:
	CO2	0.6mm .024"	40A		(-3v) 11.0V	(0v) 14.0 v	(+3v) 17.0v
					130A	(-3v) 18.1v	(0v) 21.1v	(+3v) 24.1v

	CO2	0.8mm  030"	40A		(-3v) 11.5v	(0v) 14.5v	(+3v) 17.5v	
					180A	(-3v) 18.3v	(0v) 21.3v	(+3v) 24.3v

	CO2	0.9mm .035"	55A		(-3v) 10.6v	(0v) 13.6v	(+3v) 16.6v
					180A	(-3v) 17.5v	(0v) 20.5v	(+3v) 23.5v

CO2	AL	0.9mm .035" 70A		(-3v) 11.1v	(0v) 14.1v	(+3v) 17.1v
					180A	(-3v) 16.2v	(0v) 19.2v	(+3v) 22.2v

110v MMA	20A & 56.5v to 180A & 56.5v

110v TIG	10A & 17.0v to 180A & 17.0v

110v Manuel MIG (CO2), MAG (Mixed gas), Flux
		2.0 m/min	10.0v to 26.0v
		11.0 m/min	10.0v to 26.0v

	AL	2.0 m/min	10.0v to 26.0v
		15.0 m/min	10.0v to 26.0v

110v Senergic AL	.035"	65A		(-3v) 10.0	(+2v) 10.1v	(+3v) 11.1v
							180A	(-3v) 13.0v	(0v) 16.0v	(+3v) 19.0v

	Mixed gas uses lower voltage than CO2

110v Synergic Flux
			.030"	35A		(-3v) 10.0v	(0v) 12.7v	(+3v) 15.7v
					180A	(-3v) 15.7v	(0v) 18.7v	(+3v) 21.7v

			.035	48A		(-3v) 10.0v	(0v) 12.6v	(=3v) 15.6v
					180v	(-3v) 14.5v	(0v) 17.5v	(+3v) 20.5v

Contents:
	MIG Gun 10 feet
	Graphene Liner
	Power Adapter cord ~ 1 foot
	Gas Hose 8 Feet with 5/8-18 UNF fittings
	work Clamp 10 feet
	Electrode Holder 10 feet


PreeceProducts.com (Bend, Oregon, USA 97701)
	$12.95 Brass CGA 320 CO2 tank to CGA 580 Nitrogen/Argon Regulator Adapter (search Low to High)
	This adapter is like a coupling with two different thread sizes. The CO2 side (CGA 320) is smaller and has a ledge which the fiber washer rests on when pressed in from the CGA 580 side. and is followed with a large "o" ring which the bull nose of the argon regulator presses into. The idea is to thread the fitting onto the CO2 tank just a little tighter than finger tight (snug) so the fiber washer will be resting on the face of the CGA 320 tank valve and not supported by the ledge so when the argon regulator is threaded into the fitting it will press on both the "o"ring and also the fiber washer to produce a gas tight seal.


MIG Accessory Kits: Compatible with Lincoln/Magnum 100L & Tweco Mini #1 (Threads: Gooseneck = M9x1.25 thd; Nozzle = M11x1.5 thd; Contact Tip = M6x1.0 thd).

Amazon; 2024-06-27 (Free shipping on orders over $35.00)

	Therwen 48 Pcs Flux Core Gassless Nozzle tips Kit KP1939-1; 0.030" & 0.035" Contact Tips; $17.99 Buy 2 or more, Save 7% ($16.74 each = $33.48).

Ball Flowmeter Regulator for Argon/CO2: 

	Betooll HW9003; $19.49

	RX Weld; $21.59

	Tooliom; $22.99 (5% off = $21.85)

	YesWelder; $22.80 (1% off = $22.57)

*